en
Change language:
  • esEspañol
  • rusРусский
  • ukrУкраїнська
  • enEnglish
October 30, 2026

Damp and mould in Spain: how to tackle humedad and protect your flat from moisture

Black spots on the wall behind a wardrobe, wet window reveals, blistering paint and a musty smell that returns even after cleaning. These problems are fairly common in Spanish flats. And they are not limited to older properties along the coast. Modern homes with airtight windows, inadequate ventilation and cold sections of external walls can also suffer from excessive moisture.

How can you get rid of damp and mould in a flat in Spain without having to clean and repaint the walls again a few weeks later? The first step is to identify the source of the moisture. Condensation can be reduced through ventilation, dehumidification and addressing cold surfaces. Leaks require repairs to restore the watertightness of the building, while rising damp sometimes calls for proper damp-proofing. There is no single product that works against every type of damp.

To prevent mould growth, it is recommended to keep relative indoor humidity below 60%, preferably between 30–50%. You can check this with an inexpensive indoor hygrometer. At higher humidity levels, even surfaces that appear dry can provide suitable conditions for fungal growth, particularly in poorly ventilated corners.

In Spain, the problem is commonly referred to as humedad. This single term can describe condensation, rainwater penetrating through a façade, faulty plumbing or moisture rising into walls from the ground. The range of possible causes explains why neighbours in the same building may need completely different repairs. For some, improving extractor ventilation is enough; others need roof repairs or work to restore the protection of external walls.

DIY and building supply stores such as Leroy Merlin and Brico Depôt sell mould removers, specialist paints, sealants, water-repellent treatments and waterproofing compounds. Yet even a high-quality product cannot repair a damaged pipe or a poorly constructed roof. The sensible approach is to diagnose the problem first, eliminate its cause and only then restore the damaged finishes.

Condensation, leaks or rising damp: identifying the cause from the signs

A darkened corner of a room and a wet patch near the ceiling may look similar, but they require very different solutions. The most useful clue is often where the damage appears and what happened before it developed. Condensation, for example, frequently becomes worse during colder months, whereas water penetration through a façade may become noticeable after heavy rain. Rising damp is generally found in the lower parts of building structures that are in contact with the ground.

For an initial assessment, it helps to compare visible signs with possible moisture sources.

Signs in the flatLikely causeWhat to check
Black spots in corners, droplets on windowsCondensationVentilation, indoor humidity, wall temperatures
Wet patch after rainPenetrating dampFaçade, roof, seals around windows
Flaking plaster near the floor, white salt depositsPossible rising dampContact between the wall and the ground, condition of damp-proofing
Localised dampness near the kitchen or bathroomPlumbing leakPipes, joints, drainage system
Mould behind furniture against an external wallCondensation on a cold surfaceThermal insulation, air circulation
Shower joints that remain dampFailed sealing or inadequate dryingSilicone sealant, grout, waterproofing in the shower area

Visible signs can help narrow down the investigation, but a definitive diagnosis sometimes requires specialist testing. For instance, salt deposits may remain after an old leak, while dampness near the floor can be caused by a faulty pipe. Professionals use moisture meters, thermal imaging cameras and other inspection methods, taking the limitations of each instrument into account.

When windows, cold walls and poor ventilation are to blame

In winter, warm indoor air comes into contact with cold surfaces, and the water vapour it contains can turn into droplets. Window reveals, external corners and concrete elements that allow heat to escape more quickly are particularly vulnerable. The problem becomes worse behind large wardrobes because air circulation is restricted. The surface stays cooler for longer, and moisture evaporates more slowly.

This can also happen in flats with new double-glazed windows. Airtight windows reduce uncontrolled airflow from outside, so moisture produced by breathing, cooking and showering can build up indoors if ventilation is inadequate. Drying laundry in an enclosed room adds to the problem.

Condensation can usually be reduced without major renovation, although significant thermal bridges may require improvements to the building's insulation.

Rainwater penetration and rising damp require a different approach

A damp patch that grows larger after heavy rain is a reason to check the building's external weatherproofing first. Water can enter through cracks in the façade, damaged joints around windows or failed waterproofing on a terrace. The place where moisture appears inside a room does not always correspond to the point where water enters. It can travel through building materials before becoming visible.

Rising damp can occur on lower floors and in buildings with structures in contact with the ground. Water moves through the pores of masonry and gradually damages the plaster. White crystalline salt deposits sometimes appear on the surface. In such cases, treating the wall with a household mould remover will not solve the underlying building defect.

Where to start: reducing humidity without renovation

Buying a dehumidifier may be more useful than another tin of paint if condensation is the main cause of damp. First, however, you need to find out how indoor humidity changes throughout the day. Compare hygrometer readings in the morning, in the evening, after showering and after cooking. Persistently high readings suggest that moist air is not being removed effectively or that another continuous source of moisture is present.

Ventilation should be adjusted to the weather conditions. During cooler periods, brief but intensive airing is often more effective than leaving a window slightly open all the time, which can further cool window reveals and walls. In humid coastal weather, an electric dehumidifier may work better than opening the windows. Comparing indoor and outdoor humidity readings can help you decide which approach to use.

Drying laundry inside a flat increases the amount of moisture in the air. If you do not have a balcony, it is better to use a separate, well-ventilated room or a dehumidifier designed to handle the additional moisture. After showering, make sure the bathroom extractor fan is running and allow surfaces to dry. Spread out wet towels, bath mats and shower curtains so that they do not remain damp.

Furniture positioned against external walls should have a small gap behind it. This allows air to circulate and makes it easier to inspect the wall. If mould keeps appearing in one cold corner despite normal hygrometer readings, the insulation in that area should be checked. A cold surface can create conditions for condensation even when the overall indoor humidity is moderate.

Removing mould yourself: a step-by-step guide

Small areas of surface mould on hard materials can usually be cleaned without professional help. However, if the mould has spread extensively, plasterboard is damaged, surfaces remain wet or hidden mould is suspected, it is safer to call in specialists. People with respiratory conditions or weakened immune systems should take particular care.

Mould removal should begin only after the active source of water has been addressed.

  1. Assess the condition of the surface. Check whether the contamination is limited to the outer layer or whether the material has softened, deteriorated and started to peel away. Deeply affected porous coverings may need replacing.
  2. Prepare protective equipment. Wear a suitable respirator, such as an FFP2 mask, safety goggles and gloves. Remove items that are difficult to clean from the work area and keep children away.
  3. Remove surface contamination. On hard, non-porous materials, use water and detergent to clean the affected area carefully. Avoid dry scraping and spreading dust.
  4. Apply a specialist product if necessary. Choose a treatment suitable for the particular surface. Follow the manufacturer's instructions, contact time and ventilation requirements.
  5. Dry the underlying material thoroughly. Do not cover a damp surface with plastic sheeting, wallpaper or paint. If the plaster is badly damaged, loose sections will need to be removed and the finish repaired.
  6. Check the results. Make sure the source of damp has been eliminated, the surface has dried and no new patches are appearing. Only then should you proceed with priming and painting.

Bleach is not essential for cleaning mould. On hard surfaces, thorough cleaning with a detergent solution followed by drying is often sufficient. If you use chlorine-based products, never mix them with ammonia, acids or other cleaning agents. Such combinations can release dangerous gases.

Plasterboard, wallpaper and crumbling plaster present a more difficult problem. Mould can penetrate porous materials beyond the reach of ordinary cleaning products. Painting over an affected covering will only temporarily change its appearance. If the damage is extensive, the affected layer must be replaced after the source of moisture has been eliminated.

Leroy Merlin and Brico Depôt: what products to buy and how much they cost

Spanish DIY stores offer several categories of products for tackling damp. Their shelves contain mould removers, anti-fungal paints, anti-condensation coatings, sealants and specialist waterproofing materials. However, products with similar names are not necessarily designed for the same purpose. Check whether a product is suitable for indoor or outdoor use, compatible with the surface and subject to any specific application requirements.

Leroy Merlin stocks household cleaning products, dehumidifiers, paints and building waterproofing systems. Brico Depôt offers similar categories, including treatments for damp rooms and exterior walls. When shopping, it is more useful to focus on the type of damage than on the most prominent claim printed on the packaging.

Below are examples of published prices from Brico Depôt's product range. These are material prices excluding delivery and labour, and they may vary depending on the store and product availability.

ProductQuantityApproximate price
Montó anti-damp paint750 ml11,95 €
Evalux anti-condensation paint750 ml13,50 €
Montó anti-damp paint4 l35,95 €
Anti-condensation paint4 l37,95 €
SikaMur damp-proof barrier600 g30,45 €

When calculating your budget, comparing the price of individual containers is not enough. You need to consider how much product is required per square metre, the number of coats and compatibility with the existing finish. Sometimes old plaster needs to be removed, an anti-fungal treatment applied or a specialist primer used before painting. This preparation work can significantly increase the overall cost.

Anti-fungal and anti-condensation paints: which should you choose?

Anti-fungal paint is designed to limit mould growth on painted surfaces. It is applied to previously cleaned and prepared surfaces where there is still a risk of high humidity. Such products can be useful in bathrooms or kitchens, provided the ventilation is working properly.

Anti-condensation paint serves a different purpose. Manufacturers use specialist fillers and formulations that can affect surface properties and the formation of condensation. Its effectiveness depends on the conditions of use, coating thickness and the temperature of the underlying surface. An ordinary coat of this paint cannot replace proper insulation where there is a significant thermal bridge.

Anti-damp products also vary. Some are designed to protect interior surfaces against stains, while others create coatings with particular water-repellent properties. Certain products can be applied to substrates with limited residual moisture, but this must be explicitly permitted in the instructions. They must not be applied over an active leak without first eliminating its cause.

Electric dehumidifier or passive moisture absorber

An electric dehumidifier is suitable for rooms with persistently high humidity levels. When choosing one, consider the room size, temperature, noise level and how the collected water is removed. Models with a humidity sensor are more convenient for regular use because they can maintain a set humidity level without running continuously.

A dehumidifier's rated capacity is usually stated for specific test conditions. In a cool bedroom, the actual amount of water collected may be lower than the advertised figure. Choosing a machine solely on the basis of its maximum litres-per-day capacity is therefore not advisable.

Passive moisture absorbers containing salt-based materials are useful in wardrobes, small storage rooms and enclosed spaces. Their effectiveness is limited by the absorber's capacity and the rate at which moisture accumulates. A larger room with persistent damp requires a more powerful solution.

Waterproofing a flat: step-by-step repairs to walls, windows and wet areas

If water is entering through an external building element, painting the interior will not provide a lasting solution. Waterproofing must block the route through which moisture enters and be suitable for the particular construction element. Different protection systems are used for façades, roofs, terraces and walls in contact with the ground. Spain's Technical Building Code sets out specific requirements for protecting buildings against moisture.

The extent of the work depends on the condition of the structure. A small section of damaged sealant can sometimes be repaired without professional help. Repairs to roof coverings, treatment of rising damp or work affecting a shared building façade require a technical assessment.

Sealing windows and small external cracks

Water around a window frame can enter through deteriorated sealant, an incorrectly constructed junction or damaged external finishes. Before making repairs, check the window system's drainage holes. These must not be blocked with sealant because they are designed to drain water that has entered the window assembly.

The procedure for a localised repair is as follows:

  1. Inspect the joint between the frame and the wall, identify damaged sections and make sure the problem is not caused by a hidden leak.
  2. Remove the old, deteriorated sealant without damaging the frame surface or adjacent elements.
  3. Clean dust and loose particles from the joint, then prepare the substrate according to the requirements of the chosen product.
  4. If necessary, insert a backing rod and apply a compatible weather-resistant sealant, observing the permitted joint dimensions.
  5. Allow the sealant to cure completely and check the condition of the joint after rainfall.

Specialist façade sealants resistant to weather exposure and movement are suitable for external joints. Bathroom-grade sanitary silicone is not always appropriate for these conditions. When selecting a product, consider the frame material, the substrate and whether the sealant needs to be painted afterwards.

Repairing a crack requires a separate assessment. If the damage is growing, extends through the masonry or is accompanied by structural movement, simply sealing it is not enough. A specialist should establish why the crack is opening before the affected area is covered with a finishing material.

Protecting terraces and roofs against rainwater

Leaks affecting flats on upper floors are often linked to failed waterproofing on a terrace or roof. Water can enter through damaged junctions with parapets, drainage outlets and cracks in the covering. Sometimes the visible damp patch is a considerable distance from the actual point of water entry. Treating the ceiling inside the flat therefore cannot replace an inspection of the external structure.

Waterproofing systems include flexible liquid-applied coatings, sheet membranes and other solutions compatible with the particular substrate. When choosing a system, consider sun exposure, movement caused by temperature changes, standing water and whether people will walk on the surface. For example, a coating designed for a roof that is not intended for regular access may be unsuitable for a terrace with frequent foot traffic.

Particular care is needed around junctions, corners and drainage outlets. Even a high-quality material will not provide a watertight seal if the substrate is poorly prepared or the application instructions are not followed. Work on the communal roof of an apartment building should be agreed with those responsible for maintaining the property.

Rising damp: why ordinary paint cannot solve the problem

Damaged plaster near the floor often makes it tempting to cover the affected area with a thick waterproof coating. Where rising damp has been confirmed, this approach can trap moisture inside the structure and accelerate damage to the finishes above the treated area. The route through which water enters must be identified first.

To limit moisture rising through masonry, specialists use various systems, including chemical injection treatments and the restoration of horizontal damp-proof barriers. The choice depends on the wall material, the condition of the masonry and whether other sources of moisture are present. There is no universal method suitable for every building in Spain.

Once the cause has been eliminated, the substrate needs time to dry. Plaster damaged by salts or deterioration sometimes has to be replaced using specialist repair materials. Applying a new decorative finish too early can cause blistering and peeling to return.

Bathrooms and kitchens: dealing with damp in areas regularly exposed to water

Black spots around a shower enclosure are usually noticed before a hidden leak beneath the tiles. However, damage that looks similar on the surface can require very different action. Mould on a silicone joint may result from repeated exposure to water and inadequate drying, while a damp wall behind the tiles can sometimes indicate failed waterproofing or faulty plumbing.

Badly affected sanitary sealant is best removed and replaced completely. Before applying new sealant, clean and dry the surface and check the condition of the joint. Applying fresh silicone over an old, contaminated layer is not advisable: adhesion will depend on the condition of the underlying material, and mould may remain beneath the new seal.

Tile grout also requires maintenance. Damaged joints should be repaired with a compatible product, but ordinary grout is no substitute for proper waterproofing in a shower area. If an adjoining wall remains damp, the concealed connections and waterproofing layer beneath the tiles will need to be inspected.

In the kitchen, the main areas to check are the space beneath the sink, drainage connections and the water supply connections to household appliances. Even a small leak can remain unnoticed behind kitchen units for a long time. If panels begin to swell or a persistent smell develops, inspect the concealed areas rather than simply treating the accessible surface with a cleaning product.

Mould in a rented flat: who is responsible for paying for repairs?

In rented accommodation, repairs can be complicated by the division of responsibilities between landlords and tenants. Spanish law requires landlords to carry out repairs necessary to keep a property fit for habitation, except where the damage has been caused by the tenant. Minor repairs resulting from ordinary use of the property are generally the tenant's responsibility.

If you discover damp, it is sensible to notify the landlord in writing straight away, including photographs and a description of the problem. Record the location of the patches, when they first appeared and the circumstances in which the damage becomes worse. Keep all documents and correspondence until the matter has been resolved.

Responsibility depends on the established cause. For example, water penetration through a shared building façade may require the involvement of the owners' association (comunidad de propietarios), while damage to a sealant joint inside the flat must be assessed in light of how it occurred. Disputed cases sometimes require an expert report.

Major work affecting the structure of the property must be agreed in advance. If a serious defect affects the property's suitability for habitation, the tenant can use the legal procedures available to request repairs. Deducting repair costs from rent without first checking the applicable legal conditions can lead to further disputes.

Keeping walls dry after repairs: how to make the results last

Once the source of water has been eliminated, it is worth monitoring the previously damaged area under different weather conditions. For example, the effectiveness of repairs around a window is easier to assess after rainfall, while measures taken to prevent condensation can be evaluated during cooler weather. At the same time, check hygrometer readings and inspect the areas behind furniture.

For details of the requirements governing structural moisture protection, you can consult Spain's Technical Building Code (Código Técnico de la Edificación). Guidance on safe mould removal and preventing regrowth is available from the US Environmental Protection Agency. These resources are particularly useful when you are unsure whether you can deal with the problem yourself or need professional repairs.

When looking for a contractor, ask for an explanation of the suspected cause of damp, a list of proposed works and details of the materials to be used. An offer to simply repaint a damaged wall without investigating the problem provides little reason to expect a lasting solution. You can compare contractors' offers and find building materials for repairs on Flagma, checking the scope of services, terms of work and product specifications.

Select category
×